Dyson DC07 Bagless Upright Cyclonic Vacuum\015 How is the belt changed on the Dyson DC07? I don’t have to change it yet, but I’m sure the time will come when that will be necessary. I clean whatever areas I can easily get to on the vacuum cleaner frequently, but fortunately have never had anything break down on it yet. I’ve had it for several years (at least five), and it’s the best vacuum cleaner I’ve ever owned. There must be some easy solution to changing the drive belt. Seems that when I remove the beater cover, I can remove only one side of the beater easily, but not the side that the drive belt goes around. What’s the secret to easily remove the beater bar and access the drive gear inside the plastic motor housing? Even if I don’t ever have to replace the drive belt, I’d like to be able to remove it so that I can perform additional cleaning inside the motor housing area. Thanks!\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Take the end of your belt and insert it into your belt loops with the loop on the front left side of your pants. Thread the strap end through each loop, pulling the belt through as you go. Once you reach the last loop, buckle your belt.
The noise from Oxygen vacuum cleaner never reached above 75 dB in our test. Compared to the Dyson, which reached above 90 dB, the Electrolux Oxygen is without a doubt a more silent and better designed machine.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
.
.The other end of the drive belt the part you cant see goes to a clutch.
.The clutch unit has 2 belts one is clutch to motor the second is clutch to brush roller.
.You obviously look after your machine because you say you have had no problems with belts or clutch for 5 years.
.Both belts & clutch can be worked on but its alot to explain so look at this site for service manuals.
.http://dysonmanuals.llc.nu/
.There are three (3) basic things that will cause the brush roll not to spin..
.1. When handle is upright, brush roll is OFF..2. When switch is set for HARD surface, brush roll is OFF..3. Broken/worn FLAT belt or V Belt, brush roll will not spin.
.
.I noticed that the brush roll was not spinning when my vacuum was set for CARPET. After removing the cover I noticed that the V belt was loose, I thought the belt was worn so I purchased a correct replacement belt and installed it, but the new belt was also loose and when I turned the large flat belt pulley it did not turn the V belt pulley at the same time..
.I double checked the surface setting and I had the vacuum switch set for carpet, but still when I released the handle out of the upright position the brush roll would still not spin..
.My aggravation finally led me to this posting on FixYa’s website..
.The first thing I did was checked the screw to the left of the V belt as suggested by ejmjr5 and this did nothing to solve the problem or create more tension on the V belt, even when the upright handle was not in the upright position..
.After playing around with the surface setting control switch/nob I notice that when I moved the switch out of the HARD surface setting and over to CARPET, I had thought that the switch was set for CARPET as it visually appeared, but I was not pushing the switch over hard enough to click it into the CARPET setting mode..
.VOILA, the brush roll now spins correctly even though the V belt seams to be too loose for the pulley..
.You really have to force the switch into the CARPET setting. Be sure that you hear the switch/nob click into place..
.Now you can effectively clean up after that hangover of a party!.
.Burp!
.
.Although this site doesnt actually cover the DC14 yet, the DC14 is very similar to the DC07 so as regards dissassembling the machine, and replacing the clutch, my experience is that the DC07 info will enable you to do the job.
My brush head is not turning and with the lever set to engage the drive there is still considerable slack in the final drive belt.
There appears to be only a bearing deflecting the belt, should there be a pully or other device mounted on this bearing? There is so much slack a
Unfortunately to fix it you must send it to one and that would be more expensive than a new one. Just junk this chinese POS and buy another chinese POS.