Bissell ProHeat Turbo Deep Cleaner Upright Steam Vacuum\015 I have a bissell proheat turbo 2x microban steam cleaner. I can not find the mannual for my system. I have filled it correctly, with water and solution. It comes on but the brushes do not turn nor does the water disperse? Should I have 2 bets or only one? I am only seeing one belt, could this be the problem? What download can I find for free to find the mannual for this model? Please help?\015
How to Identify and Fix Common Vacuum Problems ?
Our sources include academic articles, blog posts, and personal essays from experienced Vacuum Technicians :
Before you begin using your Bissell Carpet Cleaner, it`s important to make sure that the surface of your carpets is free from dirt and debris. To do this, use a regular vacuum cleaner to remove any loose particles or hair before beginning your cleaning session.
Relevant Questions and Answers :
the most relevant questions and answers related to your specific issue
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101 .
.
.hgkklgh
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
.
.fkj
Here’s a quick link to tips to help take care of your issue:
.
http://www.bissell.com/FAQDetail.aspx?id=1124&cid=ccsocial
.
Here is a tip that will give you all the information you need to fix your Bissell Proheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101
You can download and print the instruction manual in PDF format by clicking this link.
Please note: Adobe PDF Reader is required to view this manual. Click here to download the latest version of Adobe Reader.
Hope this solves your problem. Thanks for using FixYa.
I have a Bissell Proheat Select Pet 2X that extracts fine, but WILL NOTX put out the water / solution to be extracted. What to do ? Thank you for your time and consideration ~ Tamara / Email:[email protected]
.
.Unplug the Bissell. Remove the water container pieces from the top of the base. You’ll probably reveal two red plastic pieces mounted in the Bissell’s base, about .75″ x .75″. These spray water on your brushes when you press the water-and-soap trigger at the top of the Bissell’s handle. These water sprayers tend to clog. See the metal spring running up the hose, behind each red water sprayer? As you squeeze the red plastic sides of one red water sprayer, use a screwdriver or other tool under the spring to wedge up the hose, to release the sprayer from its mount in the base. Stick a finger in the hole of the base of the Bissell where the sprayer was mounted and run it around the edges there including on the underside of the base to clean out any gunk you can find. Clean any gunk you can off the red water sprayer with an old toothbrush.
.
.Now you need to remove the water sprayer from the hose. You need a pair of pliers. Use the pliers to squeeze the brass colored clip that is keeping the red water sprayed mounted to the end of the small hose there. Move the clip down the hose so it compresses the spring and is no longer on the red plastic water sprayer. Now you can twist and pull the red water sprayer out of the end of the hose. You’ll need a little hand strength to do this. Just be careful not to break the water sprayer by using a tool. They’re not particularly delicate, but breaking one would render your Bissell useless until it was replaced, so use a little care.
.
.When you’ve removed a red water sprayer from the hose, put the outer end of the red water sprayer in your mouth and seal your lips around it, and try blowing through it. You can’t blow air through it, right? It’s clogged. Open up a paper clip and push it back-and-forth through the small hole in the end of the water sprayer back towards its middle. You’ll probably push out a line of white mineral deposits. Clean them off the water sprayer with the old toothbrush, and try blowing through the water sprayer again. If air passes through clearly, you’ve fixed it. Now you have to put it back together. Push the water sprayer back on the end of the hose. Use the pliers to reposition the brass clip on the end of the hose over the water sprayer. Push the red water sprayer back into position in the base of the Bissell.
.
.Now do the same for the other red water sprayer.
.
.I had a problem when I fixed this on mine this morning, because when I pulled one water sprayer off, the hose advanced up under the spring and I couldn’t reattach the red water sprayer, because it couldn’t reach the end of the hose. So try to use the brass clip or some other means (rubber band, tape, another clip) to keep the hose from crawling up inside the spring after you pull the red water sprayer off the hose. If the hose gets up under the spring anyway, despite your best efforts, I fixed this by removing the six screws on top of the Bissell base (the surface of which the water tank mounts on top of), and then pried it up. You can pull out the hose, reattach the red water sprayers to the hoses, position the hose *very carefully* inside the base (there are mounts under there they need to fit into, so you don’t break anything), push the red water sprayers through the mount holes and mount them, and then reattach the screws to the base.
.
.There’s something else you may need to do that can help get the water flowing. This one’s easier. The Bissell uses pumps, which need to be primed. Sometimes an air pocket inside the machine keeps water from flowing. To prime the pumps, separate the two water tank pieces. Fill the base as usual and mount it on the Bissell without the top water tank piece. Plug the Bissell in and **turn it on**. (The Bissell must be running to do this.) Kneeling on the floor in front of the Bissell, reach up and press the soap and water release trigger at the top of the Bissell’s handle and hold it in as if you wanted water to go through. On top of the water tank is a plastic grommet hole about 1 inch in diameter, through which you pour water to fill the tank. Seal that hole with the flat of your hand. You’ll feel a bit of suction. Lift your hand up and down a few times. Release the trigger and repeat a few times. Now that you’ve cleaned out your water sprayers and primed the Bissell’s internal pumps, I’m hoping water will GUSH through your Bissell once again.
.
.As you probably have learned the hard way, as I did, it’s VERY important to do a lot of cleaning of the Bissell after each use, more than the manual tells you to do. Clean the bottom of the unit. Empty all the water. Thoroughly rinse out both water container pieces. Unscrew the three clear plastic pieces, one in front, two on the sides, that surround the brushes, and rinse them thoroughly in water. Clean off the brushes and all the lint and gunk around and above the brushes. (A water spray bottle and toothbrush are helpful here.) Tip the machine and blow all the water out of the hole in the base. Release the red clip springs on the red water sprayers and blow on them. Doing this will slow the failure of the Bissell. It’s a great little machine for the money, but it does have a learning curve and need more pampering than a vacuum cleaner, doesn’t it??
.
.Good luck!
.
.
– Check to see if the machine will spray through the hose with the setting on tools. If it does, the pump is fine. Continue troubleshooting.
.
– Check for debris on spray tips. Clean them with a soft brush (on old tooth brush works well). The spray tips may be lifted out for easier access.
.
– Ensure the tank lid is properly attached to the bottom of the tank. To attach this properly, remove the Water Tank from the machine. Hook the front window onto the lip of the bottom container and then allow the window with lid to cover the complete tank. Secure the latch on the back of the bottom tank to the back of the tank lid. THE TANK LID CANNOT BE ATTACHED PROPERLY IF THE BOTTOM TANK IS ALREADY INSTALLED IN THE MACHINE.
– Check the bottom of the Water Tank and the Formula Tank to make sure each has a red auto-load gasket attached. Make sure the Water Tank and the Formula Tank are seated properly. Depress the x on this gasket to ensure this depresses and release back out. Liquid from the tank should dispense.
.
– Remove the handle completely and re-attach. Once the handle is re-attached, re-attempt to spray.
.
.
If the machine continues to not spray, check the following:
.
REMOVE THE COLLECTION TANK:
• Make sure the unit is set to water rinse
• Remove the smart mix bottle and fill it with water only
• Place the smart mix bottle into the collection tank reservoir
• Run the unit and try to spray. If the machine sprays, you will be able to see the water level decreasing in the smart mix bottle and you will need to replace the bottom tank. It is possibly warped.
.
Here is a tip that will give you all the information you need to fix your BissellProheat Vacuum Problem.
Bissell Proheat Upright Wet/Dry Vacuum Problems
heatman101.
..mn.,b
